Amplificador Boss 2500w Mono Block Gratis Kit Instalacion #4

Descripción

*ARTICULO NUEVO
*GARANTIA POR DEFECTOS DE FABRICA
*ENVIO GRATIS A LA PUERTA DE SU HOGAR

Amplificador Clase A/B para Subwoofers BOSS AR2500MK

El amplificador BOSS AR2500MK es un potente amplificador que maneja una potencia estable de 938 watts a 4 Ohm, pero también da una potencia estable de 1875 watts a 2 Ohm, alcanza una potencia máxima de 2500 watts.

*MONOBLOCK
*TOPOLOGIA CLASE A/B
*2 OHM ESTABLE
*SUMINISTRO DE ENERGIA MOSFET PWM
*ENTRADAS RCA Y NIVEL DE ALTAVOZ
*FILTRO DE PASA BAJO
*REFUERZO DE GRAVES
*CONTROL DE SUBWOOFER A DISTANCIA

EL KIT INCLUYE
*CABLE DE CALIBRE 4GA.
*PORTAFUSIBLES CON FUSIBLE AGU 60A
*CABLE DE TIERRA DE CALIBRE 4GA.
*CABLE CALIBRE 18GA. AZUL
*RCA DE ALTO RENDIMIENTO
*CABLE DE CALIBRE 16 ALTAVOZ
*TUBO PARA EL CABLEADO.

Armor 2500W Monoblock, Class A/B Amplifier Dimensions 14.25"L 6.5"W 2.56"H

2500 W MAX Power 1 Channel
1875 W X 1 RMS @ 2 ohm
938 W X 1 RMS @ 4 ohm
Monoblock, Class A/B, MOSFET Power Supply
High and Low Level Inputs
Variable Low Pass Crossover, Variable Bass Boost
Include Remote Subwoofer Control
Dimensions: 14.25" L x 6.5" W x 2.56" H


2 Ohm Stable

The lowest impedance accepted by this amplifier is 2 ohms. Amplifiers that are 2 ohms stable produce more power resulting in more volume. This amp can comfortably power speakers or subwoofers with all channel(s) being used at a load of 2 ohms.



Class A/B

Class A/B amplifiers have long been known for their ability to produce great quality sound while performing more efficiently than pure Class A amplifiers. We have developed a specific linear circuitry that further reduces distortion while increasing both sound quality and power output.



High and Low Level Inputs

An amplifier with both high-level and low-level inputs provides flexibility by allowing you to build an audio system using virtually any standard factory or aftermarket source unit. High-level (speaker level) inputs accept the signal from the speakers, while low-level (RCA) inputs accept the signal from the pre-amp outputs of the source unit.



MOSFET

MOSFET stands for Metal Oxide Semiconductor Field-Effect Transistor. MOSFETs are used either as a switch or to amplify a signal. MOSFETs are superior to other FETs, because they require less current to operate, which makes them better suited for car audio.



Protection

If the amplifier gets too hot, the thermal protection circuit turns the amp off and allows the amp to cool down before turning it back on. If a speaker fails causing an electrical short, the protection circuit will automatically cut the output and remain in that state until the short is resolved. These safety features give you peace of mind knowing the amplifier is constantly monitoring conditions to protect itself.



Subwoofer Level Control

The ability to boost or attenuate the sub level when an amp and subwoofer are connected to the subwoofer pre-amp output.



Variable Bass Boost

Variable Bass Boost allows you to adjust the low bass within the boost range to just the way you like it.



Variable Gain Control

Variable Gain Control lets you balance the amps output with the speakers or subs the amp is driving. To much gain will lead to distortion and to little will lead to clipping.



Variable Low Pass Filter

Variable low-pass filter gives you control over the frequencies that pass through to the subwoofer.

General Specs
CHANNEL CONFIGURATION1 Channel
POWER SUPPLY TYPEMOSFET Power Supply
AMP TOPOLOGYMonoblock, Class A/B
Performance Specs
TOTAL POWER OUTPUT2500 Watts
PEAK POWER @ 2 ¿2500 Watts x 1
PEAK POWER @ 4 ¿1250 Watts x 1
RMS POWER @ 2 ¿1875 Watts x 1
RMS POWER @ 4 ¿938 Watts x 1
SPEAKER IMPEDANCE2 to 8 ¿
T.H.D. (TOTAL HARMONIC DISTORTION)0.01 %
S/N RATIO (A-WEIGHTED)105 dB
FREQUENCY RESPONSE9 Hz to 130 Hz ±1 dB
Connections, Controls, and Processing
RCA INPUTS2 Channel
HIGH LEVEL INPUTS¿
LOW PASS FILTER40 Hz to 130 Hz
BASS BOOSTVariable 0 to 12 dB
SUBWOOFER LEVEL CONTROL¿
THERMAL/OVERLOAD/SHORT PROTECTION¿
Measurement
WIDTH6.5"
HEIGHT2.5625"
LENGTH14.25"